POWER QUALITY ANALYZER PW3198 เครื่องบันทึกและวิเคราะห์ Power Analyzer พร้อมกันในเครื่องเดียว
3-Phase 4-Wire Power Quality Analyzer Compliant to IEC61000-4-30 Class A Standards with Dynamic 1300V Range,
Harmonic and Inter-harmonics Analysis Capabilities
Never Miss the Moment
● Detect power supply problems and perform onsite troubleshooting
● Do preventive maintenance to avert accidents by managing the power quality
CAT IV-600V Safety Standard
● Meets the CAT IV safety rating required to check an incoming power line
● Safe enough to measure up to 6,000Vpeak of transient overvoltage
Easy Setup Function with PRESETS
● Just select the measurement course, wiring, and clamps
● Automatic one-step setup based on measurement conditions Compliant with New International Standards
● International power quality measurement standard IEC 61000-4-30 Edition 2 Class A
● High precision with a basic voltage measurement accuracy of 0.1%
หน้าจอ 6.5-inch TFT color LCD (640 × 480 dots)
ฟังก์ชั่นบันทึกข้อมูลด้วย SD Card
Interface SD/SDHC card, RS-232C, LAN (HTTP server funtion), และ USB2.0
Power supply AC Adapter
ขนาดตัวเครื่อง 300 x 211 x 68mm (2600g)
ยี่ห้อ HIOKI, Japan
Specifications
Measurement line type |
Single-phase 2-wire, Single-phase 3-wire, Three-phase 3-wire or Three-phase 4-wire plus one extra input channel (must be synchronized to reference channel during AC/DC measurement)
|
Voltage ranges |
Voltage measurement: 600.00 V rms Transient measurement 6.0000 kV peak
|
Current ranges |
500.00 mA to 5.0000 kA AC (depends on current sensor in use) |
Basic accuracy |
Voltage: ±0.1% of nominal voltage Current: ±0.2 % rdg. ±0.1 % f.s. + current sensor accuracy Active power: ±0.2 % rdg. ±0.1 % f.s. + current sensor accuracy
|
Measurement items |
1. Transient over voltage : 2 MHz sampling 2. Frequency cycle : Calculated as one cycle, 40 to 70 Hz 3. Voltage (1/2) RMS: one cycle calculation refreshed every half cycle Current (1/2) RMS: half-cycle calculation 4. Voltage swell, Voltage dips, Voltage interruption 5. Inrush current 6. Voltage waveform comparison 7. Instantaneous flicker value: As per IEC61000-4-15 8. Frequency: Calculated as 10 or 12 cycles,40 to 70 Hz 9. 10-sec frequency: Calculated as the whole-cycle time during the specified 10 s period, 40 to 70 Hz 10. Voltage waveform peak, Current waveform peak 11. Voltage, Current, Active power, Apparent power, Reactive power, Active energy, Reactive energy, Power factor, Displacement power factor, Voltage unbalance factor, Current unbalance factor (negative-phase, zero-phase) 12. High-order harmonic component (voltage/ current): 2 kHz to 80 kHz 13. Harmonic/ Harmonic phase angle (voltage/ current), Harmonic power: 0th to 50 th orders 14. Harmonic voltage-current phase angle: 1th to 50 th orders 15. Total harmonic distortion factor (voltage/ current) 16. Inter harmonic (voltage/ current): 0.5 Hz to 49.5 Hz 17. K Factor (multiplication factor) 18. IEC Flicker, Δ V10 Flicker
|
Record |
55 weeks (with repeated recording set to [1 Week], 55 iterations) 35 days (with repeated recording set to [OFF])
|
Interfaces |
SD/SDHC card, RS-232C, LAN (HTTP server funtion), and USB2.0 |
Display |
6.5-inch TFT color LCD (640 × 480 dots) |
Power supply |
AC Adapter Z1002 (12 V DC, Rated power supply 100 V AC to 240 V AC, 50/60 Hz) Battery Pack Z1003 (Ni-MH 7.2 V DC 4500 mAh)
|
Dimensions and mass |
300 mm (11.81 in) W × 211 mm (8.31 in) H × 68 mm (2.68 in) D (excluding protrusions), 2.6 kg (91.7 oz) (including battery pack) |
Accessories |
Instruction manual × 1 Measurement guide × 1 Voltage Cord L1000 × 1 set (Red/ Yellow/ Blue/ Gray) Each 1 Black × 4 Alligator clip × 8 Spiral tube × 20 Input Cable Labels × 1 AC Adapter Z1002 × 1 Strap × 1 USB cable (1 m 3.28 ft length) × 1 Battery Pack Z1003 × 1 SD memory card 2GB Z4001 × 1
|
อุปกรณ์เสริม (แยกจำหน่าย)
Picture |
Model
|
Name
|
Specifications |
Current measurement : For power or load current measurement (1 sensor necessary for single-phase measurements, and 2 or 3 sensors required for 3-phase measurements)
|
|
HIOKI 9694
|
CLAMP ON SENSOR |
5A AC rated current, φ 15 mm (0.59 in) core dia., 3 m (9.84 ft) length
|
|
HIOKI 9660 |
CLAMP ON SENSOR |
100A AC rated current, φ 15 mm (0.59 in) core dia., 3 m (9.84 ft) length
|
|
HIOKI 9661 |
CLAMP ON SENSOR |
500A AC rated current, φ 46 mm (1.81 in) core dia., 3 m (9.84 ft) length
|
|
HIOKI CT9667 Series HIOKI CT9667-01 (φ100mm) HIOKI CT9667-02 (φ180mm) HIOKI CT9667-03 (φ254mm)
|
FLEXIBLE CLAMP ON SENSOR
|
5000/500 A AC rated current, φ 254 mm (10.0 in) core dia., Cable length: Between sensor - box 2 m (6.56 ft), Output cable 1 m (3.28 ft)
|
|
HIOKI 9669 |
CLAMP ON SENSOR |
1000A AC rated current, φ 55 mm (2.17 in) core dia., 3 m (9.84 ft) length
|
|
HIOKI 9695-02 |
CLAMP ON SENSOR |
50A AC rated current, φ 15 mm (0.59 in) core dia., Requires the Connection cord 9219
|
|
HIOKI 9695-03 |
CLAMP ON SENSOR |
100A AC rated current, φ 15 mm (0.59 in) core dia, Requires the Connection cord 9219
|
|
HIOKI CORD 9219 |
CONNECTION |
Connect with the 9695-02/ -03, Output BNC terminal
|
Leak current : For leak current measurement (not capable of power measurement) |
|
HIOKI CORD 9675 |
CLAMP ON LEAK SENSOR |
10A AC rated current, φ 30 mm (1.18 in) core dia., 3 m (9.84 ft) length
|
|
HIOKI CORD R 9657-10 |
CLAMP ON LEAK SENSOR |
10A AC rated current, φ 40 mm (1.57 in) core dia., 3 m (9.84 ft) length
|
Adapter : For clamp sensor
|
|
HIOKI ADAPTER 9290-10 |
CLAMP ON ADAPTER |
CT for 1000A AC, secondary current 1/10 of primary
|
Current measurement |
|
HIOKI CT9691-90 |
CLAMP ON AC/DC SENSOR |
SENSOR CT9691-90 DC to 10kHz (-3dB), 100A, Output 0.1 V/f.s., Cord length 2 m (6.56 ft)
|
|
HIOKI CT9692-90 |
CLAMP ON AC/DC SENSOR |
DC to 20kHz (-3dB), 200A, Output 0.2 V/f.s., Cord length 2 m (6.56 ft)
|
|
HIOKI CT9693-90 |
CLAMP ON AC/DC SENSOR |
DC to 15kHz (-3dB), 2000A, Output 0.2 V/f.s., Cord length 2 m (6.56 ft)
|